developed especially for grinding nicks in cutting dies. Pneumatic drive for high performance.The damaging of the rubber during grinding is prevented, performance of the diecutter is optimized.
simplified positioning for setting the nicks
 
Available grinding wheel size: 50x8mm or 50x10mm
Grinding Wheel Thickness: 0.2mm,0.3mm,0.4mm,0.5mm,0.6mm,0.7mm,0.8mm,0.9mm,1.0mm,1.2mm,1.5mm,2.0mm,
 
Product Parameter : 
 	 			Electricity voltage
 			220V
 		
 			Maximum Torque
 			Adjustable
 		
 			No-Load Speed
 			0-24000RPM
 		
 			Color
 			Yellow/Blue/Green
 		
 			Automatic Grade
 			Semi-Automatic
 		
 			Packing
 			1set/box
 		
 			Net Weight
 			2.5kg
 		
 			Usage
 			Die cutting Nick Grinding
 		
 			Dimension
 			180*60*68mm
 		
 			Delivery tools
 			4pcs
 		
 			Free grinding wheel per set
 			10pcs
 		
 			Warranty service
 			6 months
 		
Advantage:
 
 1. Versatile pneumatic powered nicking grinder produce clean, perpendicular nicks at consistent&adjustable depths.
 
 2. Operating with less noise and vibration
 
 3. Steady position of the devices on die-boards due to 4 removable pins below the base.
 
 4. Nicks width from 0.2mm to 2.0mm by using different grinding distance thickness.
 
Manual Instructions1. Check the air source, air pressure stable or not 
 
2. Check the machine screws etc.
 
3. Change the grinding wheel according to needs, adjust the depth valve(If not use high precision position, pls lock the depth valve to the rock bottom position, which will do the nick grinding jobs according to the pressure power) 
 
4. Wear gloves, protective glass, masks 
 
5. Connect to air source( suggest to hang up the air hose)
 
6. Pls drop 3 drops pneumatic oil to the air inlet, plug in the air hose. Rotate to right to open the grinder. Then slowly idle for a few seconds, rotate to left to close 
 
7. Put the wooden die cutting board smoothly on the table(suggest not to use sponge rubber before nick grinding, as resistance increases) 
 
8. Rotate to right to open the grinder, increase the speed. Use thumb and first finger to hold the machine when the rotation speed gets stable. Then put the machine in the front side of the steel rules, move it to the grinding position(use wheels to adjust the position) and gently press the machine to start nicking. Move stably in turn. Pay attention that must gently press and handle 
 
9. After finish the nicking job, rotate to left to close. Unplug the air hose and use 3 drops pneumatic oil to the air inlet, then plug to the air hose and open the grinder to idling for a few seconds. After that close the air source, clean the machine body and keep in proper position 
 
Product Picture Show :

Pneumatic Angle Die Cutting Machine Nick Grinding Adjustable 220V

Die Cutting Creasing Matrix

Die Cutting Rules

Die Ejection Rubber

Creasing Matrix Cutter

Anvil Cover For Die Cutting

Die Cutting Tool

Nick Grinder

Carton Waste Stripping Machine

Paper Drill Bit

Gravure Printing Doctor Blade

Die Cutting Accessories

Adhesive Double Tape

Paper cutting stick

Cleaning Sponge

Rubber Blanket

Stamping Foil

Pneumatic Angle Die Cutting Machine Nick Grinding Adjustable 220V

Manual Instructions

pneumatic angle die grinder

electric angle die grinder

auger drilling machine

Electricity voltage	220V
Maximum Torque	Adjustable
No-Load Speed	0-24000RPM
Color	Yellow/Blue/Green
Automatic Grade	Semi-Automatic
Packing	1set/box
Net Weight	2.5kg
Usage	Die cutting Nick Grinding
Dimension	1806068mm
Delivery tools	4pcs
Free grinding wheel per set	10pcs
Warranty service	6 months